A500 Gr.B/C Preheat for SMAW (low-hydrogen) — 1-1/2" to 2-1/2"

SMAW (Low-Hydrogen)

Low-hydrogen SMAW (E7018/E7016) uses basic-coated electrodes requiring rod oven storage, assigned to Category B in Table 5.11.

E7018 is the default electrode for structural fillet and groove welds on common building steels. Rod ovens should hold at a minimum of 250°F per D1.1 Clause 7.3.2.1; exposure time out of the oven is limited to 4 hours maximum per Table 7.1. For overhead position, use 3/32" diameter rods to control puddle size. Vertical-up stringer beads provide the best fusion on thicker members.

SMAW-LH Tips for Common Structural Steels

For A500 Grade B/C cold-formed HSS (46–50 ksi yield), E7018 at 120–150 A handles fillet welds for tube-to-baseplate, tube-to-gusset, and tube-to-tube connections where FCAW or GMAW access is constrained. The shorter electrode length of E7018 (14" long) can be an advantage in tight clearance tube joint configurations. Avoid starting welds on HSS cold-formed corner radii — position starts on flat.

Typical values for reference — always verify against your approved WPS and electrode manufacturer data.

Why SMAW (low-hydrogen) for A500 Gr.B/C at 1-1/2" to 2-1/2"

Why SMAW (low-hydrogen) for A500 Gr.B/C at 1-1/2" to 2-1/2"? SMAW (low-hydrogen) delivers 3-5 lb/hr deposition — compared to <a href="/welding/preheat-calculator/a500-bc/saw/1-1-2-to-2-1-2-inch/">SAW</a> at 15-40 lb/hr. Position capability: all positions. Suitability: field and shop.

A500 Gr.B/C

ASTM A500 Grade B (46 ksi [315 MPa] minimum yield) and Grade C (50 ksi [345 MPa] minimum yield), as AWS D1.1:2025 Table 5.6 lists them in Group I, cover cold-formed welded and seamless structural tubing — round, square, and rectangular HSS sections. These are the standard tubular members in building frames, trusses, and signage structures, produced in wall thicknesses from 16 gauge (0.065") up to 5/8" for rectangular and 1/2" for round. Table 5.11 assigns both Category A and B preheat requirements. The cold-forming process work-hardens the corners, producing corner radii with higher hardness (up to 20% increase) and reduced ductility compared to the flat faces. This affects welding behavior at corner locations, particularly on heavily loaded connection details where weld starts or stops near corner radii can create initiation points for fatigue cracks.

Why This Preheat for A500 Gr.B/C with SMAW-LH

Cold-formed structural tubing for HSS sections in frames and trusses. With low-hydrogen SMAW-LH, this combination falls under Category B rather than Category A — E7018 low-hydrogen electrodes produce typically 4-8 mL/100g diffusible hydrogen under proper rod oven conditions. The 150°F minimum preheat is lower than what non-low-hydrogen SMAW would require at the same thickness because SMAW-LH significantly reduces the driving force for hydrogen-induced cracking in the heat-affected zone.

Typical Applications for A500 Gr.B/C

Standard for HSS columns in office buildings, hollow section trusses in warehouse roofs, exposed architectural tube steel, sign structures, solar panel racking frames, greenhouse frames, and guard rail posts. A500 tube-to-tube moment connections require through-plate or diaphragm detailing to transfer forces across the closed section. Slotted gusset connections into HSS bracing members are a signature fabrication detail requiring careful fit-up and beveling of the gusset plate. Common sizes include HSS 6x6x3/8 and HSS 8x8x1/2 for columns, HSS 4x4x1/4 for bracing, and HSS 10x6x3/8 for rectangular beam applications. The cold-formed corner radius creates a heat-affected zone consideration that differs from hot-rolled shapes when planning multi-pass weld sequences. Round HSS pipe columns are also common, typically HSS 6.625x0.280 through HSS 12.750x0.500 for mezzanine posts and canopy supports. Fillet welds connecting HSS to cap plates and base plates are the most frequent weld joint detail.

Why Preheat Matters at 1-1/2" to 2-1/2"

Heavy plate with significant restraint and thermal mass — preheat is critical to maintain slow cooling for hydrogen escape.

Other Steels with SMAW (low-hydrogen) at 1-1/2" to 2-1/2"

A500 Gr.B/C with SMAW (low-hydrogen)

Try Different Combinations

Use the interactive preheat calculator to look up any steel, process, and thickness combination from D1.1:2025 Table 5.11.

A500 Gr.B/C Welding Guides