Pré-aquecimento de A633 Gr.E para SAW — over 2-1/2"

SAW (Submerged Arc Welding)

SAW submerges the arc beneath granular flux for highest deposition rates, flat/horizontal only. Category B in Table 5.11.

For pressure vessel longitudinal and circumferential seams, SAW is the primary process. Tandem or multi-wire configurations on specialized manipulators achieve consistent quality over seam lengths exceeding 40 feet. Flux basicity index per ASME Section II Part C determines the mechanical properties of the weld deposit.

SAW Tips for Pressure Vessel and Low-Temperature Steels

For A633 Grade E (60 ksi yield, Category C, Q&T/NT), SAW requires a higher-strength wire-flux combination — F8A4-EA2 or F8A6-EM12K provides 80 ksi weld metal tensile matching. Category C preheat minimum: 50°F up to 3/4", 150°F up to 1-1/2", 225°F up to 2-1/2", 300°F above. The normalized-and-tempered condition means HAZ properties are sensitive to SAW heat input — limit to 40–55 kJ/in on thick sections.

Typical values for reference — always verify against your approved WPS and electrode manufacturer data.

Filler Metal for SAW

Wire: EM12K or EL12 with matching flux (AWS A5.17). Common combo: F7A2-EM12K. Diameter: 3/32" or 7/64". Flux type: active (A) for single-pass, neutral (N) for multi-pass. Voltage: 28-34V. Current: 400-800A depending on joint size. Travel: 12-24 ipm.

Typical values for reference — always verify against your approved WPS and electrode manufacturer data.

A633 Gr.E

ASTM A633 Grade E is the highest-strength grade in this specification with 60 ksi minimum yield and 80 ksi minimum tensile strength (for plates up to 4”). Produced as normalized and tempered plate, it provides exceptional notch toughness with CVN testing at -60°F (15 ft-lbs transverse). Its higher strength level places it in Category C of Table 5.11, with correspondingly higher preheat requirements than the A/C/D grades. The quenched-and-tempered condition means carbon content is higher (0.22% max) with controlled manganese (1.15-1.50%) and silicon (0.15-0.50%), producing a CE-IIW of approximately 0.44-0.50. Like all Q&T steels, maximum interpass temperature must be respected to avoid degrading the tempered microstructure in the heat-affected zone during multi-pass welding.

Por que Este Pré-aquecimento para A633 Gr.E com SAW

Highest-strength A633 grade at 60 ksi yield requiring Category C preheat. The higher strength level of this steel places it in Category C of Table 5.11, which carries elevated preheat requirements compared to Category B grades. At 300°F minimum with SAW, the submerged arc process with granular flux produces controlled hydrogen levels, with flux condition being the primary variable, but the preheat must still ensure the cooling rate stays slow enough to prevent hydrogen-induced cracking in this higher-hardenability material.

Aplicações Típicas de A633 Gr.E

Found in heavy-duty crane runway girders for steel mills, offshore jacket legs, polar Class vessels, cold-region bridge main members, large-span roof trusses in Arctic facilities, and load-bearing elements in LNG terminal structures. A633 Gr.E combines 60 ksi yield with excellent low-temperature toughness (CVN testing at -60°F), making it suitable for primary structural members in environments where both high static loads and extreme cold coincide. Procurement lead times for A633 Gr.E plate can be 12-16 weeks due to limited domestic production, and plate availability above 2" thickness may require international sourcing. Repair welding requires the same preheat procedures as original fabrication to maintain the guaranteed toughness properties. Filler metal selection must provide tensile matching (80 ksi minimum) and cold-temperature CVN values that equal or exceed the base metal specification. Weld mockups for offshore and LNG applications typically undergo CTOD or wide-plate testing.

Por que o Pré-aquecimento Importa em over 2-1/2"

The heaviest sections demand the highest preheat in Table 5.11. Multi-pass sequences require maintaining interpass temperature throughout.

Outros Aços com SAW em over 2-1/2"

A633 Gr.E com SAW

Experimente Diferentes Combinações

Use a calculadora interativa de pré-aquecimento para consultar qualquer combinação de aço, processo e espessura da D1.1:2025 Tabela 5.11.

Guias de Soldagem de A633 Gr.E