A537 Cl.1/2のSAW用予熱 — 1-1/2" to 2-1/2"

SAW (Submerged Arc Welding)

SAW submerges the arc beneath granular flux for highest deposition rates, flat/horizontal only. Category B in Table 5.11.

For pressure vessel longitudinal and circumferential seams, SAW is the primary process. Tandem or multi-wire configurations on specialized manipulators achieve consistent quality over seam lengths exceeding 40 feet. Flux basicity index per ASME Section II Part C determines the mechanical properties of the weld deposit.

SAW Tips for Pressure Vessel and Low-Temperature Steels

For A537 Class 1/2 heat-treated pressure vessel plate (50–60 ksi yield), SAW F7A2-EM12K handles vessel shell seams with consistent heat input and weld profile. Class 2 Q&T condition requires interpass temperature monitoring — maintain below 400°F to preserve the tempered microstructure. Neutral flux is essential on multi-pass seams; active flux can alter weld metal composition across successive layers by transferring deoxidizing elements.

Typical values for reference — always verify against your approved WPS and electrode manufacturer data.

Why SAW for A537 Cl.1/2 at 1-1/2" to 2-1/2"

Why SAW for A537 Cl.1/2 at 1-1/2" to 2-1/2"? SAW delivers 15-40 lb/hr deposition — the highest deposition rate among available processes. Position capability: flat and horizontal only. Suitability: shop only.

A537 Cl.1/2

ASTM A537 Class 1 and Class 2 are heat-treated carbon-manganese-silicon steel plates for pressure vessels. Class 1 is normalized (50 ksi yield, 70-90 ksi tensile up to 2.5"); Class 2 is quenched and tempered for higher strength (60 ksi yield, 80-100 ksi tensile up to 2.5"). Both fall under Category B in Table 5.11, requiring low-hydrogen processes for their improved strength and toughness properties. Carbon content is limited to 0.24% max, but the manganese range (0.70-1.35%) and silicon (0.15-0.50%) contribute to a CE-IIW of approximately 0.40-0.46. A537 Class 2 Q&T plates require careful attention to maximum interpass temperature to avoid re-austenitizing the heat-affected zone and degrading the tempered microstructure achieved during mill heat treatment.

A537 Cl.1/2とSAWでこの予熱が必要な理由

Heat-treated pressure vessel plate with normalized and quenched-tempered options. This steel is prequalified only with low-hydrogen processes under Table 5.11. With SAW, the submerged arc process with granular flux produces controlled hydrogen levels, with flux condition being the primary variable. The 150°F minimum preheat balances the steel’s strength level and carbon equivalent against the hydrogen control provided by SAW. Non-low-hydrogen SMAW is not an option for this grade under D1.1 prequalified WPS.

A537 Cl.1/2の代表的な適用例

Applied in cryogenic storage tanks for LNG and liquid nitrogen, elevated-temperature pressure vessels in chemical processing, heavy-wall reactor components, and nuclear containment liner plates. A537 Class 2 quenched-and-tempered plate serves in vessels requiring both high strength and superior impact toughness at sub-zero testing temperatures. Shell course welds and head-to-shell junctions are the primary high-restraint joints where preheat compliance is most critical. Impact testing temperatures for cryogenic service can be as low as -150°F, requiring CVN testing at the design minimum temperature plus a safety margin. The quenched-and-tempered condition of Class 2 means interpass temperature maximums (typically 400-450°F per the qualified WPS) must also be controlled to avoid re-austenitization of the heat-affected zone. Vessel head pressing and spinning from flat plate introduces residual stress concentrations at the knuckle radius that influence the welding sequence for head-to-shell circumferential seams.

1-1/2" to 2-1/2"で予熱が重要な理由

Heavy plate with significant restraint and thermal mass — preheat is critical to maintain slow cooling for hydrogen escape.

SAWと1-1/2" to 2-1/2"における他の鋼材

A537 Cl.1/2とSAW

別の組み合わせを試す

インタラクティブ予熱計算機を使用して、D1.1:2025 表5.11のあらゆる鋼材・プロセス・板厚の組み合わせを検索できます。

A537 Cl.1/2溶接ガイド